Check us out on
Facebook to see our
latest work and read
the latest DJ's
Painting News
Facebook to see our
latest work and read
the latest DJ's
Painting News
| 2011 DJ's Painting, Inc. 108 South Main Street Old Forge PA 18518 |
Mascoat Industrial
Mascoat Industrial-DTI is designed to be a multiple purpose coating that solves
insulating and Corrosion Under Insulation issues. This thermal insulation coating
product fulfills niche market areas of temperatures under 400°F on all types of
substrates.
Mascoat Industrial-DTI thermal insulating coating works not only to reduce
temperatures, but also provides energy savings, thermal insulation and personnel
protection all in an easy spray-on application. Since the product is applied in 20 mil
(0.50 mm) coats directly to the substrate or primer, it provides excellent corrosion
protection as well.
Mascoat Industrial-DTI thermal insulating coating employs only the best materials
and has been specifically engineered in our own formulation lab for thermal
insulating performance and long lasting durability. Our coatings are capable of
sustained working loads of 400°F and peak temperatures up to 500°F (260°C).
Mascoat Industrial-DTI is designed to be a multiple purpose coating that solves
insulating and Corrosion Under Insulation issues. This thermal insulation coating
product fulfills niche market areas of temperatures under 400°F on all types of
substrates.
Mascoat Industrial-DTI thermal insulating coating works not only to reduce
temperatures, but also provides energy savings, thermal insulation and personnel
protection all in an easy spray-on application. Since the product is applied in 20 mil
(0.50 mm) coats directly to the substrate or primer, it provides excellent corrosion
protection as well.
Mascoat Industrial-DTI thermal insulating coating employs only the best materials
and has been specifically engineered in our own formulation lab for thermal
insulating performance and long lasting durability. Our coatings are capable of
sustained working loads of 400°F and peak temperatures up to 500°F (260°C).
* Saving total installation time when compared to conventional insulation methods
* No cutting, tapping or special hangers
* No special fabrications needed
* Adheres to virtually any material and eliminates the potential for surface
corrosion or Corrosion Under Insulation (CUI)
* The coating is a non-combustible, non-flammable, thermal insulation Class 1 (A)
fire rated product
* Water based, one-part coating and has no "pot life"
* Can be applied to working substrates up to 400ºF
* Lightweight (5.0 pounds per gallon). Approx 0.07 lbs/sq. ft. at 20 mil DFT
(0.50mm)
* Can be easily "touched up" after minor structural repairs
* Contains no harmful chlorides
* Successive coats will increase insulating capabilities
* No cutting, tapping or special hangers
* No special fabrications needed
* Adheres to virtually any material and eliminates the potential for surface
corrosion or Corrosion Under Insulation (CUI)
* The coating is a non-combustible, non-flammable, thermal insulation Class 1 (A)
fire rated product
* Water based, one-part coating and has no "pot life"
* Can be applied to working substrates up to 400ºF
* Lightweight (5.0 pounds per gallon). Approx 0.07 lbs/sq. ft. at 20 mil DFT
(0.50mm)
* Can be easily "touched up" after minor structural repairs
* Contains no harmful chlorides
* Successive coats will increase insulating capabilities
*If a site survey is requested, charges may apply.
Taken from Macoat.com :
Our client installed Mascoat Industrial– DTI Thermal Insulating Coating in their Port
Everglades facility. The coating was applied over a primer to a thickness of 200
mils. The tank already had conventional insulation on the sides.
The Chief Engineer of the facility reports that they are now achieving a higher
internal temperature of the product with one heating unit than they were with two
heating units before the application. Amazingly, they are now able to turn off the
heater over the weekend to prevent overheating of the product as well as to save
energy costs. Prior to installing Mascoat Industrial-DTI they ran both burners 24/7
without attaining current temperature levels.
Before the application, the tank top temperature was 134°F on the top and 154°F
on the rim around the top. After completion of the application, the tank top
registered at 95°F and the rim around the top was 98°F. Temperatures taken on
April 11, 2007 after the coating had fully cured showed a temperature reading of
94°F all around the top and sides while the ambient temperature outside the tank
was 78°F and the air vapor temperature was 235°F inside the tank.
Additionally, the Chief Engineer stated, “I am pleased with the inspectability of the
top, the ease and safety of maintenance personnel being able to walk on the top,
and the low maintenance of Mascoat Industrial–DTI as compared to conventional
insulation”. He also noted that the flash cooling affect and CUI are no longer issues
with the use of the coating. He is currently considering replacing conventional
insulation with the coating where he can to reduce maintenance costs and improve
performance in areas all over his current facility.
Our client installed Mascoat Industrial– DTI Thermal Insulating Coating in their Port
Everglades facility. The coating was applied over a primer to a thickness of 200
mils. The tank already had conventional insulation on the sides.
The Chief Engineer of the facility reports that they are now achieving a higher
internal temperature of the product with one heating unit than they were with two
heating units before the application. Amazingly, they are now able to turn off the
heater over the weekend to prevent overheating of the product as well as to save
energy costs. Prior to installing Mascoat Industrial-DTI they ran both burners 24/7
without attaining current temperature levels.
Before the application, the tank top temperature was 134°F on the top and 154°F
on the rim around the top. After completion of the application, the tank top
registered at 95°F and the rim around the top was 98°F. Temperatures taken on
April 11, 2007 after the coating had fully cured showed a temperature reading of
94°F all around the top and sides while the ambient temperature outside the tank
was 78°F and the air vapor temperature was 235°F inside the tank.
Additionally, the Chief Engineer stated, “I am pleased with the inspectability of the
top, the ease and safety of maintenance personnel being able to walk on the top,
and the low maintenance of Mascoat Industrial–DTI as compared to conventional
insulation”. He also noted that the flash cooling affect and CUI are no longer issues
with the use of the coating. He is currently considering replacing conventional
insulation with the coating where he can to reduce maintenance costs and improve
performance in areas all over his current facility.
 |
 |
 |
 |
 |
 |
 |
609-685-0562 |
